FRITZ!DECT 301 – Service - Base de connaissance

FRITZ!DECT 301 – Service

Using a FRITZ!DECT smart button in the home network

The FRITZ!DECT smart button, for example FRITZ!DECT 400, is integrated into your home network via an encrypted DECT connection (DECT ULE). With the smart button you can control outlet switches, for example FRITZ!DECT 200, radiator controls, for example FRITZ!DECT 301, and with FRITZ!OS 7.20 or later also FRITZ!DECT LED lamps. You can either switch outlet switches individually or together as a group, and you can also use the smart button to activate templates. For example, you can attach the smart button to an easily accessible location in order to conveniently operate sockets that are difficult to reach. Or you can simply push a button to activate the desired heating profile that you saved as a template.

Note:All instructions on configuration and settings given in this guide refer to the latest FRITZ!OS for the FRITZ!Box.

Requirements / Restrictions

  • FRITZ!DECT 400 can only be used with FRITZ!Boxes equipped with DECT base stations and FRITZ!OS 7.01 or later, except for FRITZ!Box 7412.
  • A maximum of ten FRITZ!DECT smart buttons can be registered with the FRITZ!Box.

1 Establishing a DECT connection

  1. Push the "DECT" connection button on the top side of the FRITZ!DECT smart button until you hear a signal tone.
  2. Within 2 minutes: Push the "DECT" button or the "Fon/DECT" button on the FRITZ!Box. Hold down the button for at least 6 seconds until the "DECT" or "Info" LED on the FRITZ!Box starts to flash. The FRITZ!Box is in registration mode as long as the LED flashes. The connection is established and the smart button is displayed with the connection status "Connected" in the "Smart Home" menu of the FRITZ!Box user interface.

2 Defining general settings for the FRITZ!DECT smart button

  1. Click "Home Network" or "Smart Home" in the FRITZ!Box user interface.
  2. Click "Smart Home" in the "Home Network" menu or click "Device Management" in the "Smart Home" menu.
  3. Select "All Smart Home devices" or the group of devices from the drop-down list.
  4. Click the (Edit) button for the FRITZ!DECT smart button.
  5. Click on the "General" tab.
  6. Under "Name", enter a name of your choice for the smart button.
  7. Under "Push Service Settings", enable the option "Push service enabled" so that you receive an email if the battery is low, the radio connection is lost, or there are errors.
  8. Click "OK" to save the settings.

3 Defining what happens when button is pressed

You can trigger different switching actions by pushing the button briefly or holding it down. These switching actions are defined on the tabs named [name of button: short] and [name of button: long]:

  1. Click "Home Network" or "Smart Home" in the FRITZ!Box user interface.
  2. Click "Smart Home" in the "Home Network" menu or click "Device Management" in the "Smart Home" menu.
  3. If available, select "Button" from the drop-down list.
  4. Click the (Edit) button for the FRITZ!DECT smart button.
  5. Click on the tab named [Name of the button: short]. On this tab you define what happens when the button is pushed briefly.
  6. Enable the desired option under "Standby".
  7. Under "Select Action", specify whether you want to switch smart home devices or apply smart home templates.
  8. If you enabled "Switch Smart Home devices", select the desired devices or groups under "Switch Smart Home devices" and define the switching and switching period.
  9. If you enabled "Apply Smart Home Templates", select the desired template under "Apply Smart Home Templates".
  10. Click "OK" to save the settings.
  11. Repeat steps 6 - 10 on the tab named [Name of the button: long]. On this tab you can define what happens when the button is pushed and held.